- ICOM 756 PRO II CABLE DRIVERS
- ICOM 756 PRO II CABLE SOFTWARE
- ICOM 756 PRO II CABLE PC
- ICOM 756 PRO II CABLE DOWNLOAD
PTT keying is via the interfaces built-in USB comm port RTS signal or you can choose to PTT over the CAT commands if your transceiver supports this.
ICOM 756 PRO II CABLE PC
The interface plugs into a free USB port on your PC and to your transceiver CAT and Data/PKT ports.
ICOM 756 PRO II CABLE DRIVERS
The in-built sound card drivers are included in your operating system and the interface will pop up as a generic USB PnP Sound Device.
ICOM 756 PRO II CABLE DOWNLOAD
Just follow the provided instructions to download the FTDI drivers. This interface is fully wired for your PC and transceiver. The interface allows you to dedicate your digital mode working to the external sound card and its independent level setting controls leaving your PCs internal card for normal Windows functions. Our Latest Digimode-4 interface provides a single USB connection to your PC and has both built-in USB CAT control and its own built-in USB Sound Card.
ICOM 756 PRO II CABLE SOFTWARE
USB CAT Control and Audio Interfacing of your Icom Transceiver allowing you to fully utilise software such as WSJT-X, FLDigi, Ham Radio Deluxe, Echolink, PSK31, DM780, N1MM Logger, MixW and many more. If you see a "Sold Out" message at checkout, please check back with us in a few days when we have produced some more. Our Digimode-4 interfaces are incredibly popular and so there is high demand for them. The interface used the highly reliable FTDI UART comm port chipset. CAT control allows you to set/get the frequency and mode of your transceiver. The interface gives you CAT control of your transceiver via a built in USB Comm port. The interface has a built in PTT function and can be used without a CAT interface. This frees up your PCs internal sound card for normal windows functions. The interface has a built in external USB Sound Card based on C-Media CM108 chip. Please note that some of these applications offer enhanced functionality when you also have CAT control of the radio. Perfect for use with WSJT-X, FlDigi, Ham Radio Deluxe (DM780), Echolink and many others. Suitable for any AFSK and Digital mode such as FT8, JT9, PSK31, WSPR ect. We use icons shown below to guide you to the best choice for your equipment setup. You can also choose to use your PCs internal sound card to generate/decode your Digimode signals or to use an external sound card interface to free up your PCs sound card for normal use. We offer a large range of interfaces to ensure maximum compatibility with modern and older PCs and digimode software. Secure gently two screws on the motor clutch.Icom CAT control and Digital mode interfaces to use software such as Ham Radio Deluxe, FLDigi, WSJT-X to operate PSK31, FT-8, JT9, JT-65, Echolink and many other AFSK modes. NOTE - good idea is to add small drop of machine oil, or silicon grease, but just "small" drop.Īfter reassembly the cover don't forget to check if brake nozzle fit in right direction as marked before.Īttach the motor to ATU chassis, put again attention that brake nozzle should is positioned as on the picture, with variable capacitor at his max capacitance (closed). Last thing we need is to secure upper cover of the motor - screwdriver with small 100g hammer or electric pliers will do the job.
Otherwise You'll have to open the cover again, or pray not to destroy the motor turning it by hand later. Assure that it's almost same as on my pics. NOTE: Before securing the cover, check orientation of the main output shaft with metal nozzle. Now all we need is to restore the motor to it's factory state starting with repaired rotor, and cooperating wheels in reverse order. Let the epoxy solidify, and after few hours ( or minutes ) carefully examine the surface of the magnet, bottom and upper ring, remove any glue marks or dirt with sharp knife.
0 kommentar(er)
